Reset Procedures
Tools Needed:
- Soft cloth
- Power source access
- User manual (optional)
Step-by-Step Reset Methods
- Basic Power Reset: Turn off the dishwasher at the power source, wait 2 minutes, then restore power to reset the control system.
- Factory Reset: Press and hold the Start button for 3-5 seconds until all lights flash, then release to restore factory settings.
- Program Reset: Press and hold the Program button and Rinse Aid button simultaneously for 5 seconds to cancel current cycle.
- Drain Reset: If dishwasher won't drain, press and hold the Start and Cancel buttons together for 10 seconds to reset drain pump.
- Heating Element Reset: Turn off power for 15 minutes to allow heating element to cool and reset thermal protection.
- Water Supply Reset: Check water supply valve is fully open and press Reset button if water flow error persists.
- Complete System Reset: Disconnect from power for 30 minutes to clear all error codes and reset entire system.
Error Codes
| E01 / E1 | Water Supply Error - Check water inlet |
| E02 / E2 | Drainage Error - Check drain hose and filter |
| E03 / E3 | Water Leakage Detected - Check seals and hoses |
| E04 / E4 | Temperature Sensor Error - Reset required |
| E05 / E5 | Heating Element Fault - Check heating system |
| E09 / E9 | Motor Circuit Error - Professional service needed |
| E15 / E15 | Door Switch Error - Ensure door is properly closed |
| E24 / E24 | Water Level Sensor Error - Reset water system |
Indicator Light Patterns
- Flashing Start Light: Reset in progress - wait for completion
- All Lights Flashing: System error - perform complete reset
- Single Light Flashing: Specific function error - check manual
- No Lights: Power issue - check electrical connection
For persistent error codes, contact Bosch Customer Service at 1-800-944-2904 or visit Bosch-home.com
Troubleshooting
| Problem | Possible Cause | Reset Solution |
|---|---|---|
| Dishwasher won't start | Power issue, door not latched, child lock active | Power reset, check door closure, disable child lock |
| Not cleaning properly | Spray arm blockage, filter clogged, wrong program | Clean spray arms, reset filter system, program reset |
| Water not draining | Drain hose clogged, pump blocked, filter dirty | Drain reset, clean filter, check drain hose |
| Leaking water | Door seal damaged, overfilling, loose connections | Check seals, reset water level sensor, tighten connections |
| Unusual noises | Foreign objects, spray arm obstruction, pump issue | Remove objects, reset pump, check spray arms |
| Not heating water | Heating element fault, thermal cutout, sensor error | Heating element reset, thermal reset, sensor reset |
Reset Sequence for Common Issues
- Water Flow Issues: Power reset → Check water supply → Reset water sensor
- Drain Problems: Clean filter → Drain reset → Check drain hose
- Heating Problems: Thermal reset → Heating element reset → Complete system reset
- Control Panel Errors: Soft reset → Power reset → Factory reset
Maintenance
Regular Filter Cleaning
Clean the filter system monthly to prevent blockages and ensure optimal performance. Reset filter indicator after cleaning.
Spray Arm Maintenance
Check spray arms for obstructions regularly. Reset spray arm rotation sensor after maintenance to ensure proper function.
Door Seal Inspection
Inspect door seals quarterly for wear or damage. Reset door sensor after seal maintenance or replacement.
Descaling Procedure
Perform descaling every 3-6 months depending on water hardness. Reset water hardness settings after descaling.
Rinse Aid System
Maintain rinse aid levels and reset rinse aid indicator after refilling to ensure proper dispensing and spot-free results.
Salt System Reset
Reset water softener system after adding salt to ensure proper regeneration and water softening performance.
Maintenance Reset Procedures
Filter Reset
After cleaning filter, press and hold Program 1 and Program 3 for 3 seconds
Rinse Aid Reset
After refilling rinse aid, press Rinse Aid button for 5 seconds until light turns off
Salt System Reset
After adding salt, press and hold Extra Dry and Program 4 buttons simultaneously
Water Hardness Reset
After changing water hardness setting, press Start button three times quickly
Child Lock Reset
Press and hold Program 2 and Start buttons for 5 seconds to toggle child lock
Factory Default Reset
Hold Program 1 and Cancel buttons for 10 seconds to restore all factory settings
Manual Downloads
Bosch Exxcel Series Manuals
SMS6ECI00E
Exxcel 6 Series Reset Guide
SMS8ECI00E
Exxcel 8 Series Reset Guide
SMS4ECI00E
Exxcel 4 Series Reset Guide
SMS2ECI00E
Exxcel 2 Series Reset Guide
Popular Companion Models
SMS88TW00E
Exxcel Pro Reset Guide
SMS68TW00E
Exxcel Plus Reset Guide
SMS46TW00E
Exxcel Compact Reset Guide
SMS24TW00E
Exxcel Slim Reset Guide