Heat Element Replacement Guide
Tools Needed:
- Phillips screwdriver
- Flat-head screwdriver
- Multimeter
- Wire cutters/strippers
- Replacement heating element
- Safety gloves and goggles
Step-by-Step Replacement
- Safety First: Disconnect the dishwasher from power supply and turn off water supply.
- Access Heating Element: Remove the lower rack and access panel to expose the heating element.
- Disconnect Wiring: Carefully disconnect the electrical wires from the heating element terminals.
- Remove Old Element: Unscrew the mounting brackets and remove the faulty heating element.
- Install New Element: Position the new heating element and secure with mounting brackets.
- Reconnect Wiring: Attach electrical wires to the new heating element terminals.
- Test Installation: Reconnect power and run a test cycle to verify proper heating function.
Specifications
Model Number | SMS40C02GB |
Type | Built-in Dishwasher |
Color | Stainless Steel |
Place Settings | 12 Place Settings |
Heating Element Power | 1800W |
Voltage | 220-240V, 50Hz |
Energy Rating | A++ |
Water Consumption | 9.5L per cycle |
Dimensions (HxWxD) | 81.5 x 59.8 x 55 cm |
Weight | 32 kg |
Noise Level | 48 dB |
Warranty Information
- Full Warranty: 2 years parts and labor
- Heating Element Warranty: 5 years
- Additional Coverage: Optional extended warranty available
For warranty service, contact Bosch Customer Service at 1-800-944-2904 or visit Bosch-home.com
Key Features
EcoSilence Drive
Brushless motor technology provides quiet operation and long-lasting reliability with minimal maintenance requirements.
ActiveWater Technology
Intelligent water management system that optimizes water usage based on load size and soil level for maximum efficiency.
VarioSpeed Plus
Reduces cycle time by up to 65% while maintaining excellent cleaning performance through optimized water pressure and temperature.
Home Connect
Wi-Fi enabled for remote control and monitoring via smartphone app, allowing program selection and cycle status tracking.
PerfectDry
Advanced heat exchange drying system that uses residual heat to naturally dry dishes without additional energy consumption.
AquaStop
Complete protection against water damage with double-layered hoses and automatic leak detection system.
Heating System Technology
Pre-Heating
Rapid water heating to optimal temperature for efficient cleaning performance
Temperature Control
Precise temperature regulation for different program requirements
Energy Efficient
Optimized heating cycles to minimize energy consumption
Safety Features
Overheat protection and automatic shut-off for safe operation
Drying Support
Assists in the condensation drying process for spot-free results
Sanitization
High-temperature cycles for hygienic cleaning and bacteria elimination
Troubleshooting
Problem | Possible Cause | Solution |
---|---|---|
Dishes not drying properly | Faulty heating element, rinse aid empty | Check heating element, refill rinse aid |
Water not heating | Heating element failure, thermostat issue | Test heating element, check thermostat |
Error code E15 | Heating system malfunction | Check heating element and temperature sensor |
Long cycle times | Heating element inefficiency | Replace heating element, check water temperature |
Poor cleaning results | Insufficient water temperature | Verify heating element operation |
Unusual noises from heating area | Loose heating element, scale buildup | Secure heating element, descale if necessary |
Error Codes
- E09: Water supply issue - Check water inlet
- E15: Heating system error - Check heating element and sensor
- E21: Water drainage problem - Check drain pump and hose
- E24: Temperature sensor failure - Replace sensor
- E25: Overheating protection - Check heating system
- E32: Leakage detection - Check for water leaks
Manual Downloads
Current Model Manuals
SMS40C02GB
12 Place Settings Dishwasher
SMS46GI01G
14 Place Settings
SMS88TW01G
16 Place Settings
SMS25AW01G
10 Place Settings
Popular Previous Models
SMS50E32GC
13 Place Settings
SMS53L12GC
12 Place Settings
SMS24AW01G
10 Place Settings
SMS68TW01G
14 Place Settings